Guides · 2026-10-20
Refacing kitchen cabinets that were built in place
Refacing is usually explained with factory boxes in mind, sound underneath and wearing tired doors. Some older kitchens have no boxes at all. Open a door and you are looking at the wall. The cabinets were built right there by a carpenter, and the question is whether that kind of kitchen can be refaced at all.
Can cabinets a carpenter built in place be refaced?
Usually, yes. A built-in-place kitchen hangs on a solid wood face frame fastened to the wall framing, and that frame is often sounder than a particleboard box. What changes is the work. Every door and drawer front is made to its own opening, and the frame needs a decision of its own. That is still cabinet refacing in Marion, with more measuring at the start.
These kitchens turn up in the foursquares and bungalows near downtown and often in the older postwar houses around town. Some have been painted so many times that nobody in the house knows what wood is under there.
The frame is the part worth keeping. It was cut and fitted to that room, and it is solid wood. Pulling it out means repairing the wall behind it, and a new set of boxes still has to be made to fit a room that is no longer square.
How can you tell your kitchen cabinets were built in place?
Open the doors and look inside before you look at anything else. A factory cabinet is a closed box with its own back and sides, and a built-in-place cabinet is a frame across the front with the room doing the rest. A few signs give it away.
- One face frame runs the whole length of the wall, with no seam or doubled stile where one cabinet would meet the next.
- There is no cabinet back. The plaster or the wall boards show inside, usually painted the same color as everything else.
- The shelves rest on strips of wood nailed to the walls or the partitions, not on pins or clips.
- The drawers slide wood on wood. Pull one out and there are no metal slides, only a runner worn shiny along its length.
- Doors along one run are close to the same size but not quite, and the gaps around them are not quite even either.
A kitchen with factory boxes on one wall and built-in-place cabinets on another is common in a house where the kitchen was added to over the years.
Why does every door have to be made for its own opening?
The openings were cut on site, one at a time, and they vary by small amounts. A refacing door ordered by standard size, set into a frame like that, leaves a gap that is wide on one side and tight on the other, and the eye catches it all the way down the run. So each door and drawer front is measured where it will hang and built to that opening.
The measure also settles how the new doors sit. Many original doors in these kitchens sat partly inside the opening, or fully inside it with the frame showing all around. New doors can be made to lap over the frame, which is the look most people know from newer kitchens, or to sit inside the opening the way the originals did. That is a style choice, and in an older house the inside-the-opening door is often the one that looks like it belongs.
A pull-out added at the same time is built to the opening too, for the reasons covered in the guide to fitting pull-outs into older cabinets.
What happens to a face frame with decades of paint on it?
Layers of paint round over the frame’s edges, chip around the spots where hands land, and build up enough that a new door will not sit flat against the frame. The buildup comes off before anything else happens. Then the frame is either covered with wood veneer to match the new doors or refinished on its own, depending on the look and on what the wood underneath turns out to be.
In a house this old, the paint gets tested for lead before anyone sands it.
Veneer suits a frame that will be painted along with the new doors, or one where the wood underneath is a patchwork of repairs. Refinishing suits a frame that turns out to be good hardwood with clean joints, where the original wood is part of the point. Either way, the frame gets its finish in the same job as the doors, so the two match when the doors go up.
Are the old drawers and shelves worth keeping, and what does it cost?
The wood-runner drawers can keep running with new fronts if they still slide and the boxes are solid, or they can be replaced with new drawer boxes on metal slides. The second choice takes more work here. A slide has to fasten to something, and behind the frame there is no box side, only open space to the wall. A mount gets built into that cavity first, square to the opening, and the slide goes on the mount.
Fixed shelves on their wood strips can stay where they are. They can also come out in favor of shelves that adjust, which means building a side inside the cavity to carry the shelf supports. In upper cabinets the old fixed shelves are often fine. In the bases, where pots and small appliances live, people tend to want drawers.
Some runs are not worth it. A frame that has pulled away from the wall or a layout that has to change points the other way, and the questions in refacing or replacing apply here the same as anywhere.
For the work itself, refacing a Marion kitchen typically runs $4,000-$12,000, depending on door count, door style and how much of the frame is covered. Doors made to sit inside the opening as the originals did add roughly 15-20%, since each one has to fit its opening on every side. The project ranges sit together on the page showing what refacing costs next to new cabinets. A built-in-place kitchen is priced from the measure, opening by opening.
Related service: Cabinet refacing and refinishing in Marion