Marion · Prospect · Caledonia · Bucyrus - built for Marion County homes Talk through a project: (740) 736-3805
Marion Cabinet Co. - engraved brass plate on quarter-sawn oak Marion Cabinet Co.

Guides · 2026-10-12

Cabinet organizers for the kitchen cabinets you are keeping

A kitchen that feels short on cabinets usually has the space and no way to reach the back of it. The deep base with one fixed shelf holds a front row you use and a back row you find by kneeling on the floor with your phone’s flashlight. If the boxes are staying, the job is getting that back half to come out to you.

Can organizers go into the kitchen cabinets you already have?

Yes, as long as the boxes are sound. Roll-out trays in the deep bases, a pull-out behind the sink door and a unit that reaches into the blind corner all go into cabinets that stay on the wall. Each one is built to the opening as measured, the way any custom home storage starts, instead of picked off a store shelf by cabinet width.

Nothing else in the kitchen has to change. The doors and counters stay, and the boxes stay screwed to the wall. The work happens inside, one cabinet at a time, and the kitchen is usable the whole way through.

Why does a store-bought roll-out kit not fit an older cabinet?

The kit is sized to the box, and an older face-frame cabinet’s opening is narrower than the box behind it. The frame laps in on each side, the hinge side takes a little more, and the slides need clearance on both sides of the tray. A tray sized to the inside of the box catches on the frame before it ever reaches the door.

The cabinets in most older houses, Marion’s ranches among them, are face-frame construction, with a hardwood frame on the front of every box and the doors hung on it. A kit sized to the box fits better in a frameless cabinet, where the opening runs nearly the full width of the box, than it does in these.

The door adds its own problem. A door that cannot swing all the way open, because it meets the next cabinet, the refrigerator or a wall, hangs partly across the opening, and a tray running out at full width hits its edge. Hinges sometimes help. Usually the tray gets narrower.

A built tray handles all of that by starting from the frame. Spacers go onto the inside of the box sides, packed out to the frame line, so the slides mount flat and the tray runs past the frame and the half-open door with room to spare. In a double-door base with a fixed post down the middle, the answer is two trays, one behind each door, rather than one wide tray that cannot get past the post.

Which cabinet in the kitchen gives back the most?

In most kitchens it is the deep base cabinet with a single fixed shelf. It holds the most and shows the least, and two roll-out trays in place of that shelf put everything in it within reach from standing. After that, the cabinet beside the range and any tall, narrow cabinet with fixed shelves.

  • The deep base with one shelf. Two trays usually, with the lower one tall-sided for pots and the upper one shallow for lids and baking pans.
  • The base next to the range. Pans and skillets come out on a tray within a step of the burner, instead of being unstacked on the floor to reach the one at the bottom.
  • The tall, narrow cabinet. Trays stacked one above the other like drawers replace shelves that were too deep and too dark to see past the first can.

Wall cabinets rarely earn a roll-out. Their shelves are shallow enough to see across, and a tray at shoulder height takes away more room than it gives back.

What fits under the sink around the pipes?

Trays shaped around the plumbing. A U-shaped tray wraps the trap, or two narrow trays run left and right of the drain, and a garbage disposal gets its own cutout. A shallow tray up top holds what every sink base holds, the dish soap, the sponges and the roll of trash bags, where it can be reached without bending.

The sink base is the one cabinet where the tray is drawn around what is already in there, so the measure takes in the drain and the disposal, and the trays leave the shutoff valves reachable. Moving a pipe or fixing a drip is the plumber’s work. A sink base with a damp, stained or soft floor stops the organizer conversation until that is fixed, since trays need a sound floor and sound sides to mount to.

What can be done with the blind corner?

The blind corner is the part of a corner base cabinet that runs behind the cabinet next to it, where nothing can be seen from the door. There are two honest answers. Fit a pull-out that brings the hidden shelves forward through the opening, or close the corner off as a dead panel and stop pretending it is storage.

A corner pull-out is hardware on a track, and the track takes width. The narrower the opening, the less shelf comes out through it, and in an older kitchen with a slim corner door, what reaches the front can be smaller than people expect. Swing-out shelves that pivot through the door work in some corners. Two-part units that slide the back shelves sideways into the opening work in others. Both need the opening measured before anyone decides.

When the opening is too tight for either, a dead corner is a fair call. The roasting pan used twice a year can still live back there behind a plain shelf, and the money goes to the bases that get opened every day.

When is a cabinet too far gone to fit with organizers?

When the box cannot hold a slide. Particleboard that crumbles around a screw, a sink base that is swollen or water-stained, and boxes that have racked out of square all fail the same test. A tray on slides needs two parallel sides that hold fasteners, and a box without them binds the tray or lets it drop.

The quickest check is the one an installer makes. Open the cabinet, look at the sides near the front, and press on the floor of the box. Solid wood or plywood that holds its shape takes trays for years. Soft, bowed or flaking material strips out the first time a loaded tray pulls on it.

The other limit is what the kitchen is being asked to do. Trays in the three or four cabinets that matter fit into boxes that stay. Drawer banks and pullouts in every cabinet means rebuilding most of the boxes, and at that point the question becomes refacing or replacing the cabinets.

Rather put the question to a person?

Call and describe your room - you'll get the same straight answer, tuned to your actual house.

Request an estimate

Describe the room. Get a real number, in writing.

A few sentences is plenty - which room, roughly how big, painted or stained, and when you hope to have it done. You hear back from a cabinetmaker, not a call center, and the estimate arrives in writing. Prefer to start out loud? (740) 736-3805.

  • The number comes in writing before anything is scheduled - materials and labor together
  • Measured from your actual walls, floors, and ceilings - not a catalog's standard boxes
  • One Marion-area point of contact from the first measure to the last hinge adjustment

Call (740) 736-3805 - written estimate first