Marion · Prospect · Caledonia · Bucyrus - built for Marion County homes Talk through a project: (740) 736-3805
Marion Cabinet Co. - engraved brass plate on quarter-sawn oak Marion Cabinet Co.

Guides · 2026-10-27

Fitting out a storefront in an old downtown Marion building

A business that signs a lease on one of the older brick buildings downtown usually walks in with its own list: a counter, a wall of shelving, a spot for the register, something to put in the front window. The building has a list too, and most of it was written when the building went up.

What does an old downtown building change about a store’s cabinetry?

Most of what gets drawn. In an older downtown building, the floor, the walls, the woodwork already in the room and the front window settle much of the commercial cabinetry and millwork before anyone sketches a counter. A new plain-walled space starts from a blank plan, and these buildings do not.

Around the courthouse square at Main and Center, where the Marion County Courthouse has stood since the 1880s, many of the commercial buildings are older brick storefronts, often deep and narrow, with a big window at the sidewalk. Downtown Marion, Inc. runs the city’s affiliate Main Street program. Whatever the business, a building like that has usually decided these things already:

  • A wood floor that slopes toward the front or the back, or crowns in the middle over a beam or an old bearing wall.
  • Walls of brick, or plaster on wood lath, where a newer space would have studs at a regular spacing.
  • Original woodwork, a pressed-tin or plaster ceiling and a transom over the entry, all of which every new piece will be seen beside.
  • A front window that is the best display space the store has.
  • A front door, and sometimes a narrow stair, that every piece has to fit through on its way in.

The rest of this guide takes them in the order you meet them, starting at the floor.

How does a counter sit level on a floor that is not?

It stands on a base that is adjusted to the floor, not straight on the boards. A long counter or display run gets a base built or set to the floor’s actual line, so the top comes out flat and true while the floor under it keeps its slope. The toe kick or base trim is then cut to follow the floor, and no tapered gap shows along the bottom.

Old wood floors in these buildings have had a century to move. A run of counter set down on one without that work follows the dip, and you see it in use. A pen rolls toward the low end. The seam between two counter sections opens at the top. Stacking shims under a finished case is the usual shortcut, and it does not last, since the shims compress and creep under daily weight until the counter rocks.

So the floor gets read across the whole length of the run at the measure, and the base is built to it in the shop. On a floor that crowns, the level line is taken from the high point and the ends are built up to meet it. If the slope is bad enough to bother people walking across it, that is a question for the building’s owner and a flooring contractor, and the counter is built to whatever floor is there on install day.

What will hold shelving on a brick or plaster wall?

That depends on what is behind the surface, and it is settled at the measure, not on install day. Wall shelving and tall fixtures on a brick wall are anchored into the masonry itself. On plaster they fasten into whatever framing is found behind it. Where neither is sound enough, the piece stands on its own base and ties back to the wall only lightly, to keep it upright.

Plaster on lath looks like a wall that will hold anything. It is a hard skin over thin wood strips, and a loaded shelf hung on the skin alone works loose over time. Brick holds well where the mortar is sound. Old mortar is often softer than the brick around it, so where each anchor lands matters as much as the anchor. The wall shared with the storefront next door is a party wall, and anything fastened into it gets cleared with the building’s owner first.

Whether a wall can carry a heavily loaded run at all is a structural question, and it belongs to the owner and the trades who know the building. Freestanding fixtures have a quieter advantage in a leased space. When the lease ends they leave with the business, and the wall is left much as it was found.

Should new millwork copy the old woodwork or look plainly new?

Choose one and commit to it. A new piece beside original window casings, a tin or plaster ceiling and an old storefront transom either copies the existing profiles closely enough to pass as part of the building, or it reads as plainly new furniture that does not try to. The trouble comes from pieces that land in between, close to the old trim without being it.

This is the other sense of millwork, the one the lumberyards mean: the run moldings, casings, baseboard and panel trim that dress a room. In a storefront it comes up wherever something new meets the old work, a new counter front, a cased opening into the back room, a new wall that needs a baseboard. Copying a profile starts from a piece of the original or a measured section of it, and the new molding is run to that shape. Matching suits a room where the old woodwork carries the space and the casings and transom are what customers notice. Standing apart suits a store whose fixtures are meant to read as its own, a painted counter or a clean-lined case set in the old room the way a good piece of furniture sits in a hall. Under a tin ceiling, tall fixtures usually stop short of it and leave the ceiling as one surface.

Where does the display go when the front window is the whole show?

Up front and kept low, so it never blocks the view in. A window platform or a run of low cases holds the display at the glass, and people on the sidewalk can still see past it into the store. Taller fixtures step back from there toward the counter, which in a deep room usually sits well back.

Storefronts of that age are often far deeper than they are wide. The layout that works in a long narrow room puts the tall shelving down the side walls, keeps the middle open and lets the height build from the window toward the back, so the whole length of the store reads from the door. A platform also needs a way in for whoever changes the display, a step or a hinged section, since the window gets redressed more often than anything else in the store.

On the side of a downtown street that faces west, the afternoon sun comes straight through the front glass and lies across whatever is in the window for hours. A platform there wants a finish that holds up to it, and anything that fades belongs further back.

What does an old building change about the install itself?

The size of the pieces and when they go in. Every case and counter section is sized to fit through the front door and up any stair it has to climb, then built and finished in the shop, so the work on site is mostly setting, leveling and fastening. On-site time stays short, and the install can run in an evening or over a weekend while the store stays open, as the after-hours answer on our commercial page covers.

A long counter often comes in sections that join on site, with each seam placed where it reads as an intended break in the run. Before any of it is fastened to the building, the owner and the landlord have signed off on what gets anchored where.

Rather put the question to a person?

Call and describe your room - you'll get the same straight answer, tuned to your actual house.

Request an estimate

Describe the room. Get a real number, in writing.

A few sentences is plenty - which room, roughly how big, painted or stained, and when you hope to have it done. You hear back from a cabinetmaker, not a call center, and the estimate arrives in writing. Prefer to start out loud? (740) 736-3805.

  • The number comes in writing before anything is scheduled - materials and labor together
  • Measured from your actual walls, floors, and ceilings - not a catalog's standard boxes
  • One Marion-area point of contact from the first measure to the last hinge adjustment

Call (740) 736-3805 - written estimate first